Fakra extension cable set for GPS 7.5 m with 2 adapters GT5 and GT16

The antenna A10 is, according to our tests, at the moment the best antenna for optimal radio reception in camper van. The electronics, the antenna radiator and the antenna supports are perfectly matched to each other. For vehicles where the height does not matter, we always recommend the 23 cm antenna radiator. You will be thrilled!

Delivery contents:

Antenna A10
Antenna support 4, stainless steel 360*360*1,5 mm, painted white central hole d= 20 mm
Lowloss cable 7,5 m, Fakra socket - Fakra socket, for VHF
Adapter 1: Fakra plug - DIN plug
Adapter 2: Fakra plug - ISO plug

Lowloss cable 7,5 m, Fakra female - SMB female, for DAB+

Roof antenna with the following features:
- 16V antenna with long rod, length approx. 23cm
- DAB+ reception, active and low noise in the BAND 3
- VHF/FM/AM reception, active and low noise
- 12 Volt power supply via external cable 0,75 mm2 (no phantom power possible)
- low installation depth (approx. 15 mm)
- gain: FM: 9 dB
- Gain: DAB+: 14 dB
- power supply: 12 Volt, 30mA
- cable: RG 174, FM 300 mm, Fakra plug, white, code B
- Cable: RG 174, DAB+ 300 mm, Fakra plug, gray, code G

Low-Loss cables (...low loss cables) are the cables with the best electrical properties for lossless transmission of antenna signals. Our lowloss cable series has best conductance values and therefore lowest cable resistance. They are achieved by using tinned strands for the inner conductor (7*d=0,25mm), for the shield (42*d=0,11mm) and an additional aluminum foil between the PE dielectric and the shield. Only high quality Fakra plugs and sockets from Rosenberger are used. They have excellent workmanship and fit due to a special punching-bending technology of Rosenberger(Fakra-SF).

Technical data:

Characteristic impedance: 50 Ohm
Capacitance: 95pF/m
Extended POLYTHEN insulation 2.00 mm
Aluminum foil shielding and additional tinned copper braiding
Outer diameter: 3.6 mm

Note: This set replaces the previous sets:

A1T4L750UNI

A product that, when combined with our UV-resistant roof junction box, art. Nr. 15931, provides an attractive and safe roof duct. The part of the roof duct that protrudes into the junction box ensures that no water can penetrate into the vehicle when installed correctly. The roof duct is neatly sealed off on the inside

Dimensions:
Drill diameter: d=48 mm
Largest inner diameter: d=38 mm
Smallest inner diameter: d=29 mm
Largest outer diameter: d=74 mm
Width across flats for fixing nut: 54 mm
Largest possible roof thickness for fastening with nut: 36 mm
Total length: 104 mm

We recommend an adhesive sealant for sealing the roof duct, such as Sikaflex, our Art. No. 15909, or similar materials.

DEKALIN adhesive set

- paintable
- wide adhesion spectrum
- very good UV and ageing resistance

The adhesive set is ideally suited for bonding solar modules, roof feed-throughs, antenna supports and metal plates to improve antenna reception characteristics.

Delivery contents:

- 290 ml adhesive, white
- Decavator 30 ml
- Cleaning cloth set (moist/dry)
- brush
- Instruction manual

You will find gluing instructions under the tab "Documents".

The technical data sheets and the safety data sheets for individual components of the set can be found here under the tab "Documents".

Hazard statements for the decavator:
H225 Highly flammable liquid and vapour
H315 Causes skin irritation
H318 Causes serious eye damage
H361d Suspected of damaging the unborn child
H336 May cause drowsiness and dizziness
H304 May be fatal if swallowed and enters airways
H411 Toxic to aquatic life with long lasting effects.
For experienced users only.

Junction box of protection class IP68 with 4 inputs/outputs in waterproof design. The inputs and outputs have high-quality screw connections with yellow rubber seals for cable diameters 4-8 mm, 8-12 mm and 10-14 mm. It is supplied with 10 stainless steel screws and a 6-pole luster terminal block.

The junction box is ideally suited for mounting under the 15904 and 15906 antenna stainless steel plates. For this purpose, it is recommended to drill a hole with d= 32 mm on the smooth rear side. The boxes can be glued well with the decalin products Dekavator and Dekasyl MS-5 black.

Dimensions:
Largest outside dimensions: 170 mm * 152 mm * 61 mm
Inner dimensions: 112 * 92 mm * 47 mm
Quantity of screw connections: 4 pieces (M25)
Rubber seals: 4 pieces 4-8 mm, 4 pieces 8-12 mm, 4 pieces 10-14 mm
Luster terminals: 6 poles
Stainless steel screws: 10 pieces