DEKASYL MS-1 white, 290 ml, Elastic adhesive and sealant

You can fix the bracket in any groove of the router with the enclosed screws.

Features:

Mounting standard: 35mm DIN rail
Material: Carbon-free steel
Weight: 57g
Included screws: Philips flat head screw #6-32×3/16, 2pcs.
Dimensions: 82mm x 46mm x 20mm
RoHS compatible: yes

Contents:
1 clip holder with 2 screws
1 piece top hat rail

The antenna A10 is, according to our tests, at the moment the best antenna for optimal radio reception in camper van. The electronics, the antenna radiator and the antenna supports are perfectly matched to each other. For vehicles where the height does not matter, we always recommend the 23 cm antenna radiator. You will be thrilled!

Delivery contents:

Antenna A10
Antenna support 4, stainless steel 360*360*1,5 mm, painted white central hole d= 20 mm
Lowloss cable 10 m, Fakra socket - Fakra socket, for VHF
Adapter 1: Fakra plug - DIN plug
Adapter 2: Fakra plug - ISO plug

Lowloss cable 10m, Fakra socket - SMB socket , for DAB+

Roof antenna with the following features:
- 16V antenna with long rod, length approx. 23cm
- DAB+ reception, active and low noise in the BAND 3
- VHF/FM/AM reception, active and low noise
- 12 Volt power supply via external cable 0,75 mm2 (no phantom power possible)
- low installation depth (approx. 15 mm)
- gain: FM: 9 dB
- Gain: DAB+: 14 dB
- power supply: 12 Volt, 30mA
- cable: RG 174, FM 300 mm, Fakra plug, white, code B
- Cable: RG 174, DAB+ 300 mm, Fakra plug, gray, code G

Low-Loss cables (...low loss cables) are the cables with the best electrical properties for lossless transmission of antenna signals. Our lowloss cable series has best conductance values and therefore lowest cable resistance. They are achieved by using tinned strands for the inner conductor (7*d=0,25mm), for the shield (42*d=0,11mm) and an additional aluminum foil between the PE dielectric and the shield. Only high quality Fakra plugs and sockets from Rosenberger are used. They have excellent workmanship and fit due to a special punching-bending technology of Rosenberger(Fakra-SF).

Technical data:

Characteristic impedance: 50 Ohm
Capacitance: 95pF/m
Extended POLYTHEN insulation 2.00 mm
Aluminum foil shielding and additional tinned copper braiding
Outer diameter: 3.6 mm

Note: This set replaces the previous sets:

A1T4L1000UNI

Generates an additional DAB/DAB+ signal from a passive FM/VHF antenna. Amplification FM/UKW and DAB+ 20dB each Connections to the radio: DIN plug SMB socket Connection to antenna: DIN socket Also works with active FM/UKW antennas if the antenna itself does not filter the frequency band. With a phantom antenna, a phantom adapter must be inserted between the splitter and the antenna connection, e.g. 8551, as any phantom voltage from the radio is not passed through. The best results are achieved when the splitter is combined with a passive FM/UKW/DAB antenna: - 16 V antenna: ATTB_2116_01 - Flex antenna with adjustable rod from 10-115 degrees: ATTB_3940_01 - Shark/shark antenna: ATTB_3759_01 These antennas always have a piece of cable 40cm with a Fakra socket. You can then use a possibly existing Fakra cable or bring the signal into the dashboard with the extension cable Dietz: 8479 (Fakra plug - DIN plug, length 5 metres). Connect the splitter there. If the radio has an ISO antenna connection for FM, you will also need the adapter, Dietz 8300.